QSC Speaker WL2082-iBK/WH


QSC WL2082-i ลำโพง Installation line array – dual neodymium 8″ cone LF, dual titanium diaphragm, neodymium magnet compression driver HF, selectable bi-amp/tri-amp operation, 140° horizontal coverage, integral array hardware, available in black or white


WL2082-i line array

  • Installation-optimized design brings affordable and uncompromised line array performance to a broader range of venues
  • Compact and attractive appearance, available in black and white, harmonizes with any installation environment
  • Wide 140° horizontal coverage
  • Economical and easy-to-install suspension system with ample array adjustability
Configuration 2½ way, biamp or triamp Vented box
  High Frequency Dual 50 W 8Ω 1″ exit, 1.75″ titanium diaphragm, neodymium magnet assembly
Dual 200 W 16Ω 8″ woofers, 2″ voice coils, neodymium magnet assemblies, weather resistant cone
  Low Frequency 850 W, 8Ω 18″ woofer with a 4″ voice coil, ceramic magnet assembly
Frequency Response (±3 dB) 80 Hz – 20 kHz 32 Hz – 200 Hz
Frequency Range (-10 dB) 68 Hz – 22 kHz 29 Hz – 800 Hz
Nominal Impedance HF: 16Ω LF: 8Ω
LF biamp mode: 8Ω
LF triamp mode: 16Ω (×2)
Sensitivity HF: 106 dB 98 dB
LF: 97 dB (2.83 V @ 1 m)
(4 V @ 1 m)
Continuous Power Capacity 1 HF: 100 W LF: 850 W
LF biamp mode: 400 W
LF triamp mode: 200 W (×2)
Recommended Power HF: 200 W LF: 1750 W
LF biamp mode: 800 W
LF triamp mode: 400 W (×2)
Maximum Output (dB SPL at 1 m) LF: 128.5 dB / 134.5 dB
  Continuous / Peak HF: 126 dB / 132 dB
LF: 122 dB / 128 dB
Nominal Coverage Horizontal 140 degrees
Vertical: dependent on number of elements used
Cabinet Type Ported, elliptical / trapezoidal Vented subwoofer
Enclosure Material HIPS (high impact polystyrene) with UV protectant 18 mm Baltic Birch Plywood
Finish Available in black (WL2082-i BLK) or white (WL2082-i WHT) paintable Available in black (WL118-sw BLK) or white (WL118-sw WHT) paintable
Grille Perforated, formed aluminum 16 gauge powder-coated steel with cloth backing
Connectors 2 x NL-8 in parallel 2 x NL8 in parallel / 2 x NL4 in parallel
Pin Outs Pins Bi-amp Tri-amp NL8
1+/1- NC NC Pins
2+/2- NC LF2 1+/1- Sub
3+/3- LF LF1 2+/2- Pass thru
4+/4- HF HF 3+/3- Pass thru
4+/4- Pass thru
1+/1- Sub
2+/2- Pass thru
Attachment Points Integral, side plate adjustable rigging system, vertical splay adjustable in 1° increments from 0° – 10° Integral, non-adjustable (straight array only)
Dimensions 11.8″ H x 27″ W x 13.4″ D 22.1″ H x 27.6″ W x 30.3″ D
(300 mm x 686 mm x 340 mm) (562 mm x 702 mm x 771 mm)
Weight 37 lb (16.8 kg) net 111 lb (50.4 kg) net
45 lb (20.45 kg) shipping 121 lb (55 kg) shipping
Accessories Available FB2082-i: Fly-bar for WL2082-i, WL118-sw and WL115-sw. Available in black or white.
EB2082-i: Extension bar, allows WL118-sw or WL115-sw to be suspended behind WL2082-i. Available in black or white.
PB2082-i: Pullback bar for WL2082-i. For use when pulling back the bottom of the array is necessary to achieve the desired angle. Available in black or white.
AB2082-i: Angle bracket, allows greater vertical splay between WL2082-i and WL118-sw or WL115-sw enclosures in ground stacked configurations. Available in black. Requires two brackets per array, sold individually.
GS115-sw: Ground stack kit for WL118-sw or WL115-sw.
QRP-KIT-1: Kit of four (4) Quick Release Pins for use in lieu of included bolts.